All categories
Is it possible to remove the shunt action on an LK SmartComfort?
- Yes, by holding down the menu button and minus button for about 5 seconds, shunt action is turned off.
- To activate pump action, hold down the menu button and the plus button for about 5 seconds
Related products
Related pages
Did this answer help you?
I have an LK 550 AquaMix on which I have replaced the insert. I now have insufficient heat: is there anything I can do about this?
You can increase the maximum temperature. You can do this as follows:
- Turn the knob counterclockwise to (+).
- Loosen the screw and put the knob to one side.
- Then turn the knob in the "air" clockwise towards (–). This adjustment can be made incrementally, with a ¼ turn corresponding to approx. 7°C.
- Replace the knob and feel for when it grips the cog.
- Fasten the screw and then turn the knob to max (+). Maximum calibration to increase the temperature is a ½ turn
Related products
Related pages
Did this answer help you?
How do I clean the filter on a LK 520 MultiFill?
You can do so easily by following the steps below.
Did this answer help you?
What should I do if I have misplaced the air vent to my LK 550 AquaMix?
The air vent can be ordered directly from us as a spare part, article number: 187224
Related products
Did this answer help you?
The warm water from my tap is not the correct temperature: what should I do?
The temperature field can be adjusted by following the instructions in the product data sheet for the LK 550 AquaMix and LK 548 AquaKit. The product data sheet can be downloaded from our website under each product.
Related products
Did this answer help you?
Why is my safety valve leaking?
Is it OK to have water coming out of the wastepipe? When water is heated, it expands and the increased volume needs to go somewhere, meaning that your safety valve will drip.
Did this answer help you?
My mixing valve rotates in different directions: is there something wrong?
No, this is quite normal. The mixing valve will rotate randomly between ports A and B. Rotation takes place at an angle of 60°.
Related products
Unfortunately, I threw away the insulation for my LK 521 MultiFill: can I buy this as a spare part?
Yes, this is available as a spare part for size DN 25 and DN32. You can find the article number under Accessories on the product page.
Related products
Did this answer help you?
Can I replace my water meter console with a new version without adaption?
When replacing older models of the LK 580, you will need to supplement the new water meter coupling with a sleeve, article number: 016019
Did this answer help you?
Which expansion vessel should I buy?
If your expansion vessel connection is located on the long side, you should choose expansion vessel article number: 064010.
If your expansion vessel connection is located on the short side, you should choose expansion vessel article number: 5523321
Did this answer help you?
My LK SmartComfort says that the outdoor temperature sensor is missing but, as far as I know, my product doesn’t need one?
Presumably you are not receiving a signal from your room unit; check your connection.
Related products
Did this answer help you?
Is the LK SmartComfort compatible with a mixing valve from another manufacturer?
Yes, we provide mounting kits for other models, see Mounting kits on our website.
Related products
Did this answer help you?
I want to replace my 12 litre expansion vessel: which should I choose?
If your expansion vessel connection is located on the long side, you should choose expansion vessel article number: 064010.
If your expansion vessel connection is located on the short side, you should choose expansion vessel article number: 5523321.
If you are unsure, please contact Customer Support at kundsupport@lkarmatur.se
If you would prefer to speak to us in person, you can find our Customer Support telephone number on our website under Support.
Related pages
Did this answer help you?
Is it possible to upgrade LK 110 to LK 130 by purchasing and adding the indoor temperature controller? Or do I need to purchase the whole LK 130 set?
Yes it is possible to just add an indoor controller to your LK 110, and your SmartComfort will then have become a LK 130 instead.
Related products
Did this answer help you?
Why can’t I find the right spare part (sensor body) for my loading unit?
Probably because you have an older product manufactured before 2010 under the name Acaso. The Acaso loading unit always stated the opening temperature, while on current loading units we always state the return temperature. You should therefore check the attached conversion table to find the correct spare part. You can find further information in our Spare Parts and Accessories brochure on page 21, which you can find under Support/Brochures at lkarmatur.se.
Related products
Related pages
Did this answer help you?
I have an RP 12-litre expansion vessel with the port on the long side but I can’t find this product on your website.
We do have that product, it is article no. 064010
Did this answer help you?
Can I purchase spare parts for an Acaso 3-way valve in cast iron?
Yes, we have both a liner with art.no. 180125 and a gasket set with art. no.180126. You can find further information in our Spare Parts and Accessories brochure, which you can find under Support/Brochures on our website.
Related pages
Did this answer help you?
Is it possible to replace a Honeywell mixing valve with an LK 525 MultiZone with actuator?
Is it possible to replace a Honeywell mixing valve with an LK 525 MultiZone with actuator?
Related products
Related pages
Did this answer help you?
Do all LK 810 ThermoMat spare parts fit the entire range?
No, they do not. You can find the correct spare part in our Spare Parts and Accessories brochure, which you can find under Support/Brochures on our website.
Related products
Related pages
Did this answer help you?
Can you use LK's safety valves with steam?
None of LK's safety valves are designed to be used with steam.
Related products
Did this answer help you?
What is the running time of a SmartComfort?
All our SmartComfort units rotate 90 degrees in 17 seconds.
Related products
Did this answer help you?
Can I buy the air-vent for LK 560 AquaKit as a spare part?
Yes, it can be ordered with article number 187306.
You can find it under LK 560AquaKit and Accessories and spare parts on our website.
Related products
Did this answer help you?
Can you change the insert on the mixing valve LK 550 AquaMix?
Yes, spare part for the insert can be ordered at RSK 4920723. Alternatively, if you want to replace the entire valve, it can be ordered at RSK 4920708.
Related products
Did this answer help you?
How do I know which water meter console I have, and when do I need to replace it?
The entire coupling needs to be replaced.
- 580 globe valve coupling (large black wheel) – 1984
- 581 globe valve coupling (large black wheel) – 1984
Type number 580/581 is stamped on the brass housing.
Replace with
LK 583 FlowMet and replacement sleeve art. no. 016019
Replace as and when required
- 582 globe valve coupling small black wheel with a line on the wheel 1985–2000
Type number 582 is stamped on the brass housing.
Replace with
LK 583 FlowMet
LK 582 see picture below:
LK 583 FlowMet ball valve coupling 2000–
The picture shows the current design of the LK 583 FlowMet.
Related products
Did this answer help you?